Gun Belt Sizing That Starts With Your Holster
Gun Belt Sizing That Starts With Your Holster
Quick answer: Choose a gun belt by checking three separate measurements: its length around your carry setup, its width through your pants and holster attachment, and its thickness inside that attachment. The Akar Dragon sold by MyHolster uses 1.75-inch nylon webbing. That width can suit some hardware, but it will not fit a clip designed only for a 1.5-inch belt. Confirm the attachment before choosing a size.
A belt can feel comfortable on its own and still work poorly with a holster. A clip may fail to seat, a buckle may crowd the front of the waistband, or an adjustment tail may land directly under an attachment. Measuring those contact points gives you something more useful than a familiar pants size.
Start with the hardware you already own
Take the holster off and read its belt specification. Look for a stated width on the clip, loop or product page. Then measure your trouser loops. Both must accept the belt; an extra-wide strap offers little benefit if it cannot pass through your pants.
Width and thickness are different limits. A loop may accept a 1.75-inch width yet leave too little room for layered webbing or a folded adjustment section. A clip needs to close around the strap as intended, including its lower retaining edge. Do not stretch, cut or bend hardware to make an uncertain combination work.
Check length with the equipment in place. Leave usable adjustment in both directions with the clothing and equipment you actually wear. A belt already at the end of its range gives you little room to change layers or accommodate an inside-the-waistband holster.
What a gun belt adds to an ordinary belt
A holster places weight at a particular point around your waist. The belt needs enough structure to support that load without rolling or sagging. Reinforced leather and layered nylon are two ways manufacturers provide support; the material name alone does not tell you how a particular belt will behave.
Richard Mann's gun-belt selection article in Shooting Illustrated emphasizes matching belt width to the holster and leaving adjustment for different carry arrangements. His measuring method uses an existing belt that fits with the usual equipment. Apply any brand's own sizing instructions before transferring that measurement to an order.
More stiffness does not automatically mean a better fit for your body. Check whether the belt supports the holster without creating a hard pressure point when you sit. Tightening until something hurts is a reason to revisit the combination, not evidence that it now fits.
The Akar Dragon: published dimensions and available sizes
MyHolster's Akar Dragon 1.75-inch nylon gun belt listing specifies two layers of rigid nylon webbing, a Cobra buckle and adjustable fit. It does not publish the strap thickness, buckle dimensions or a load rating. Those missing measurements matter if your attachment has tight clearance.

The following size labels and supplier codes come directly from the listing. All five variants showed available on November 16, 2026. Availability can change before checkout.
| Size | Listed range | SKU / stock |
|---|---|---|
| Small | 28–34 inches | A7234_S / available |
| Medium | 34–39 inches | A7234_M / available |
| Large | 39–44 inches | A7234_L / available |
| X-Large | 44–49 inches | A7234_XL / available |
| XX-Large | 49–56 inches | A7234_XXL / available |
The catalog size graphic calls these waist sizes. The text does not explain the measurement endpoints or how much allowance to add for equipment. At a shared boundary such as 34 inches, ask which range accommodates your measured setup. Do not automatically add a fixed number of inches or treat the range as a guaranteed pants-size conversion.
Verified holster listings, with belt-fit limits separated
These products name the firearm models shown below. That verifies the catalog's intended firearm fit, not a hands-on test of every configuration. Only the paddle listing supplies a maximum belt width. The other rows identify what still needs confirmation before pairing them with the Dragon.
| Model-named product | Available variant / SKU | Belt pairing evidence |
|---|---|---|
| Glock 19 Gen 3 leather OWB paddle | Black / MASC_EFES_P2225_BL | Maximum belt width 1.75 inches; strap thickness still needs checking. Listing excludes red-dot optics. |
| Glock 17 Gen 3 leather OWB with snap loops, Style 2 | Black / MASC109_HK_BL; brown / MASC109_HK_BR | Snap loops verified; opening dimensions unpublished. Dragon pairing unconfirmed. |
| Sig P365 right-hand leather IWB with clip | Black / IC6124_CO_BL | Clip-on identity verified; clip opening dimensions unpublished. Dragon pairing unconfirmed. |

The paddle's 1.75-inch limit matches the Dragon's nominal width. It does not answer whether the entire attachment closes correctly over the actual belt thickness. The same distinction applies to other nominally matching widths.

The snap-loop photograph illustrates the attachment style. It does not establish the pictured belt's dimensions. A loop that snaps shut should also sit securely without bunching the strap or leaving the holster free to shift.

These are catalog photographs, not a documented MyHolster fit test. The blue demonstration pistols do not prove model identity. Supplier photos and codes can be shared across listings, so use the model-named product page rather than a familiar-looking image or SKU alone.
Buckles, adjustment tails and the space at your waistband
A traditional prong buckle, a ratchet and a side-release buckle adjust differently. Ratchet systems use a track; a quick-release buckle does not by itself establish how finely the belt adjusts. The Dragon listing does not provide adjustment increments or approve interchangeable buckles. Follow the instructions for the actual belt rather than another brand's cutting or assembly method.
For an appendix arrangement, check the space occupied by the buckle and adjustment tail alongside the holster attachment. For hip carry, inspect where a trouser loop forces the attachment to sit. With the firearm unloaded and ammunition removed from the fitting area, check normal seated and standing comfort before relying on the combination.
Useful order note: Send your measured waist over clothing, holster link, attachment width and any known thickness limit. Ask about buckle clearance separately. Those details help resolve a size boundary or unknown loop opening before an order.
An everyday trouser belt and a belt intended for a larger duty arrangement also have different space requirements. Check every carried attachment separately. No load rating, professional approval or suitability for additional equipment is established by the Dragon's product name.
Gun belt sizing FAQ
How much bigger should a gun belt be?
There is no single allowance that applies to every belt. Measure with your usual clothing and carry equipment, then use the specific maker's sizing method. The Dragon listing supplies size ranges but no fixed extra-inch rule.
What size belt should I buy for a 32 waist?
Small is labeled 28–34 inches on the Akar Dragon listing. A pants label of 32 alone does not confirm fit with a holster. Check your actual measurement and ask how the listed range should be applied to your setup.
How do I determine my belt size?
Measure at the height where the belt will sit, over the clothing and equipment it must accommodate. Record that measurement and compare it with the product's instructions. Confirm width and thickness clearance separately; length alone cannot establish attachment fit.
What is the best belt width for a gun holster?
Use the width specified for that holster attachment and check your trouser loops too. The Dragon is 1.75 inches wide. The selected Glock 19 Gen 3 paddle lists a 1.75-inch maximum; the snap-loop and P365 clip openings still need confirmation.